|Deployment modes||Centralized, standalone, sniffer, Cisco FlexConnect , monitor, OfficeExtend, mesh|
|Supported wireless LAN controllers||Cisco 2500 Series Wireless Controllers, Cisco Wireless Controller Module for ISR G2, Cisco Wireless Services Module 2 (WiSM2) for Cisco Catalyst 6500 Series Switches, Cisco 5500 Series Wireless Controllers, Cisco 5520 Series Wireless Controllers, Cisco FlexÂ 7500 Series Wireless Controllers, Cisco 8500 Series Wireless Controllers, Cisco 8540 Series Wireless Controllers, Cisco 5760 Wireless LAN Controller, Cisco Catalyst 3650 and 3850 Series Switches with integrated controllerCisco Mobility Express|
|802.11n version 2.0 (and related) capabilities||3×3 MIMO with two spatial streamsMaximal ratio combining (MRC)20- and 40-MHz channelsPHY data rates up to 300 Mbps (40 MHz with 5 GHz)Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx)802.11 dynamic frequency selection (DFS)Cyclic shift diversity (CSD) support|
|802.11ac Wave 1 and 2 capabilities||3×3 MIMO with two spatial streams, single-user or multiuser MIMOMRC802.11ac beamforming (transmit beamforming)20-, 40-, and 80-MHz channels PHY data rates up to 867 Mbps (80 MHz in 5 GHz)Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx)802.11 DFSCSD support|
|Regulatory Domain||B (B regulatory domain):|
– 2.412 to 2.462 GHz; 11 channels
– 5.180 to 5.320 GHz; 8 channels
– 5.500 to 5.720 GHz; 12 channels
– 5.745 to 5.825 GHz; 5 channels
|Integrated antenna||2.4 GHz, gain 3 dBi, internal omni, horizontal beamwidth 360 5 GHz, gain 5 dBi, internal omni, horizontal beamwidth 360Â |
|Interfaces||1 x 10/100/1000BASE-T autosensing (RJ-45), Power over Ethernet (PoE)Management console port (RJ-45)USB 2.0 (enabled via future software)|
|Indicators||Status LED indicates boot loader status, association status, operating status, boot loader warnings, boot loader errors|
(W x L x H)
|Access point (without mounting bracket): 8.3 x 8.3 x 2 in. (210.8 x 210.8 x 50.8 mm)|
|Weight||3.12 lb (1.41 kg)|
|Environmental||Cisco Aironet 1830i|
Nonoperating (storage) temperature: -22Â to 158 F (-30Â to 70 C)Nonoperating (storage) altitude test: 25 C, 15,000 ft.Operating temperature: 32Â to 104 F (0Â to 40 C)Operating humidity: 10% to 90% (noncondensing)Operating altitude test: 40 C, 9843 ft.
|System memory||1 GB DRAM256 MB flash|
|Input power requirements||AP1830: 44 to 57 VDC power supply and power injector: 100 to 240 VAC; 50 to 60 Hz|
Note: When deployed using a PoE specification, the power drawn from the power sourcing equipment will be higher by some amount, depending on the length of the interconnecting cable.
|Powering options||802.3af/802.3atEnhanced PoECisco local power supply, AIR-PWR-C=Cisco power injector, AIR-PWRINJ5= (Note: This injector supports 802.3af only), AIR-PWRINJ6=|
Note: If 802.3af PoE is the source of power, the USB port is disabled.